エクセルで図形のみを選択する方法。
左下の矢印をクリックする。
あ、これは図形ツールバーにあるので表示させとかないといけない。
でも、エクセルで図形を使うのは、本当は嫌い。
このブログを検索
2009/02/21
2009/01/04
QTConverter
携帯でとったムービーをムービーメーカーで編集するには、QTConverterでaviに変換するべし。
いろいろソフトがあって試してみたが、速度が変わったり音が壊れたり音しか変換できなかったりダウンロードのリンクがわけがわからなかったり時間がかかったり・・・
QTCはすぐダウンロードできてインストールも変換もあっという間だった。
・・・が、Quicktimeからaviにエクスポートできるじゃん・・・
なんか画質が劣化するっぽいけど・・・
いろいろソフトがあって試してみたが、速度が変わったり音が壊れたり音しか変換できなかったりダウンロードのリンクがわけがわからなかったり時間がかかったり・・・
QTCはすぐダウンロードできてインストールも変換もあっという間だった。
・・・が、Quicktimeからaviにエクスポートできるじゃん・・・
なんか画質が劣化するっぽいけど・・・
2008/12/23
続続続・IPsecをやってみる (NEC & FITELnet)
では次に、FITELnetとNEC
PC1 ---- F100 ---- IX2004 --- PC2
シリアルケーブル買ってきました。IX2004のために。
要は、モデムとつなぐときはストレート、PC同士はクロス、ということです。
あっさりできた。
ix2004,
FITELnet F100 x 3,
シリアルケーブル(クロス) for FITELnet、
シリアルケーブル(ストレート) for IX,
某ソフト registration・・・
Dynamipsインストール、
Catalyst引っ張り出し・・・
シリアルのストレートケーブルというのは、昔モデムに接続するときに使ったものである。多分、コンシューマ向け(?)のちっちゃいルータ(IX2004とか)は、それと同じケーブルでつなげるようにと、ストレートでつなぐようになっているのだろう。
一方、FITELnet F100はシリアルのリバース(クロス)ケーブルでつなぐ。
このケーブルは、PC同士をつないでデータ転送をするような時に使う。
私も昔、かってつないだような記憶がある。 「ある程度の大きなルータになると、PC扱いになるのでクロスでつなぐ・・・」というのは私の覚え方。
結線は
だとさ
PC1 ---- F100 ---- IX2004 --- PC2
シリアルケーブル買ってきました。IX2004のために。
要は、モデムとつなぐときはストレート、PC同士はクロス、ということです。
あっさりできた。
FITEL#sho cry isa sa [ 1] 100.0.0.2 <--> 100.0.0.1 Main Mode UP pre-shared key DES MD5 Lifetime : 600secs Current : 19secs,1kbytes mcfg config-mode: off mcfg addr: off mcfg apl-version: IKE Keepalive: dpd ICMP Keepalive: off release on addr-change: off FITEL#sho cry isa policy Protection suite priority [1] authentication method : preshared key encryption algorithm : DES - Data Encryption Standard (56 bit keys) Diffie-Hellman Group : #1 (768 bit) hash algorithm : Message Digest 5 lifetime : 600 seconds, no volume limit Disabled frequency : 0 Default protection suite authentication method : preshared key encryption algorithm : DES - Data Encryption Standard (56 bit keys) hash algorithm : Message Digest 5 Diffie-Hellman Group : #1 (768 bit) lifetime : 1000 seconds, no volume limit FITEL#sho running.cfg ! ! FITELnet-F100 ! Firmware version: V02.07(02) 032307 ! ip route 0.0.0.0 0.0.0.0 100.0.0.2 ! access-list 1 permit 192.168.1.0 0.0.0.255 ! vpn enable vpnlog enable ! ipsec access-list 1 ipsec ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 ipsec access-list 64 bypass ip any any ipsec transform-set P2-des-md5 esp-des esp-md5-hmac ! service dhcp-server ! hostname FITEL ! ip dhcp pool lan1 exit ! interface ewan 1 crypto map kyoten ip address 100.0.0.1 255.255.255.0 ip nat inside source list 1 interface exit interface ewan 2 exit interface lan 1 ip address 192.168.1.254 255.255.255.0 exit ! ! crypto isakmp policy 1 authentication prekey encryption des group 1 hash md5 idtype-pre userfqdn key ascii secret lifetime 600 negotiation-mode main peer-identity address 100.0.0.2 exit crypto map kyoten 1 match address 1 set peer address 100.0.0.2 set transform-set P2-des-md5 exit crypto security-association exit ! end Router(config)# sho running-config ! ip route 192.168.1.0/24 Tunnel0.0 ip access-list list1 permit ip src 192.168.2.0 0.0.0.255 dest 192.168.1.0 0.0.0.255 ! ike proposal ike-prop encryption des hash md5 lifetime 600 ! ike policy ike-policy peer 100.0.0.1 key secret ike-prop ! ipsec autokey-map ipsec-policy list1 peer 100.0.0.1 default ipsec local-id ipsec-policy 192.168.2.0/24 ipsec remote-id ipsec-policy 192.168.1.0/24 ! telnet-server ip enable ! device FastEthernet0 ! device FastEthernet1 ! interface FastEthernet0.0 ip address 100.0.0.2/24 no shutdown ! interface FastEthernet1.0 ip address 192.168.2.254/24 no shutdown ! interface Loopback0.0 no ip address ! interface Null0.0 no ip address ! interface AutoTunnel0.0 no ip address shutdown ! interface Tunnel0.0 tunnel mode ipsec ip unnumbered FastEthernet1.0 ipsec policy tunnel ipsec-policy out no shutdown Router(config)# Router(config)# sho ike sa ISAKMP SA - 1 configured, 1 created Local address is 100.0.0.2 Remote address is 100.0.0.1 IKE policy name is ike-policy Direction is responder Initiator's cookie is 0xfc6bbe87ce000000 Responder's cookie is 0xba77d813c2ce6e0d Exchange type is main mode State is established Authentication method is pre-shared Encryption algorithm is des Hash algorithm is md5 DH group is modp768, lifetime is 414 seconds #ph1 success: 1, #ph1 failure: 0 #ph1 hash err: 0, #ph1 timeout: 0, #ph1 resend: 0 #ph2 success: 1, #ph2 failure: 0 #ph2 hash err: 0, #ph2 timeout: 0, #ph2 resend: 0 Router(config)# Router(config)# sho ike statistics Phase1 Statistics: 1 success, 0 failure, 0 hash errors 0 config errors, 0 timeout errors, 0 resend packet Phase2 Statistics: 1 success, 0 failure, 0 request errors, 0 hash errors 0 config errors, 0 timeout errors, 0 resend packet IKE Informations: Notify message type Rcvd: 0 invalid payload type, 0 doi not supported 0 situation not supported, 0 invalid cookie 0 invalid major version, 0 invalid minor version 0 invalid exchange type, 0 invalid flags, 0 invalid message id 0 invalid protocol id, 0 invalid spi, 0 invalid transform id 0 attributes not supported, 0 no proposal chosen 0 bad proposal syntax, 0 payload malformed 0 invalid key information, 0 invalid id information 0 invalid cert encoding, 0 invalid certificate 0 cert type unsupported, 0 invalid cert authority 0 invalid hash information, 0 authentication failed 0 invalid signature, 0 address notification 0 notify sa lifetime, 0 certificate unavailable 0 unsupported exchange type, 0 unequal payload lengths 0 connected 0 responder lifetime, 0 replay status, 1 initial contact 0 keepalive, 0 keepalive ack 0 unknown type Sent: 0 invalid payload type, 0 doi not supported 0 situation not supported, 0 invalid cookie 0 invalid major version, 0 invalid minor version 0 invalid exchange type, 0 invalid flags, 0 invalid message id 0 invalid protocol id, 0 invalid spi, 0 invalid transform id 0 attributes not supported, 0 no proposal chosen 0 bad proposal syntax, 0 payload malformed 0 invalid key information, 0 invalid id information 0 invalid cert encoding, 0 invalid certificate 0 cert type unsupported, 0 invalid cert authority 0 invalid hash information, 0 authentication failed 0 invalid signature, 0 address notification 0 notify sa lifetime, 0 certificate unavailable 0 unsupported exchange type, 0 unequal payload lengths 0 connected 0 responder lifetime, 0 replay status, 0 initial contact 0 keepalive, 0 keepalive ack 0 unknown type Delete protocol type Rcvd: 0 isakmp, 0 ah, 0 esp 0 unknown type Sent: 0 isakmp, 0 ah, 0 esp 0 unknown type Router(config)# sho ipsec sa IPsec SA - 1 configured, 2 created Interface is Tunnel0.0 Key policy map name is ipsec-policy Tunnel mode, 4-over-4, autokey-map Local address is 100.0.0.2 Remote address is 100.0.0.1 Outgoing interface is FastEthernet0.0 Interface MTU is 1446, path MTU is 1500 Inbound: ESP, SPI is 0x9566dd14(2506546452) Transform is ESP-DES-HMAC-MD5-96 Remaining lifetime is 393 seconds Replay detection support is on Outbound: ESP, SPI is 0x3ae07975(987789685) Transform is ESP-DES-HMAC-MD5-96 Remaining lifetime is 393 seconds Replay detection support is on Perfect forward secrecy is off Router(config)#というわけで・・・
ix2004,
FITELnet F100 x 3,
シリアルケーブル(クロス) for FITELnet、
シリアルケーブル(ストレート) for IX,
某ソフト registration・・・
Dynamipsインストール、
Catalyst引っ張り出し・・・
シリアルのストレートケーブルというのは、昔モデムに接続するときに使ったものである。多分、コンシューマ向け(?)のちっちゃいルータ(IX2004とか)は、それと同じケーブルでつなげるようにと、ストレートでつなぐようになっているのだろう。
一方、FITELnet F100はシリアルのリバース(クロス)ケーブルでつなぐ。
このケーブルは、PC同士をつないでデータ転送をするような時に使う。
私も昔、かってつないだような記憶がある。 「ある程度の大きなルータになると、PC扱いになるのでクロスでつなぐ・・・」というのは私の覚え方。
結線は
1 --- 7&8 2 --- 3 3 --- 2 4 --- 6 5 --- 5 6 --- 4 7&8 --- 1 フレーム --- フレーム
だとさ
続続・IPsecをやってみる (Cisco & FITELnet)
ここまでは、サンプルをいれただけなのでできて当然。
問題は、異なる機種間での相互接続である。
それじゃ、まず、cisco --- FITELnet をやってみようか?
PC1 ---- F100 --- R1 --- R2
PC1: 192.168.1.10
F100: 192.168.1.254, 100.0.0.1
R1: 100.0.0.2, 192.168.2.254
R2: 192.168.2.1
R1とR2はDynamipsでemulateしたCisco7200
問題は、異なる機種間での相互接続である。
それじゃ、まず、cisco --- FITELnet をやってみようか?
PC1 ---- F100 --- R1 --- R2
PC1: 192.168.1.10
F100: 192.168.1.254, 100.0.0.1
R1: 100.0.0.2, 192.168.2.254
R2: 192.168.2.1
R1とR2はDynamipsでemulateしたCisco7200
R1#sho running-config Building configuration... Current configuration : 1811 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker ! ! no aaa new-model ! ! ip cef ! ! crypto isakmp policy 1 hash md5 authentication pre-share lifetime 600 crypto isakmp key secret address 100.0.0.1 255.255.255.0 ! crypto ipsec security-association lifetime seconds 1000 ! crypto ipsec transform-set IPSEC esp-des esp-md5-hmac ! crypto map MAP1 1 ipsec-isakmp set peer 100.0.0.1 set transform-set IPSEC match address 101 ! ! ! ! interface FastEthernet0/0 ip address 100.0.0.2 255.255.255.0 ip nat inside ip virtual-reassembly duplex auto speed auto crypto map MAP1 ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 192.168.2.254 255.255.255.0 serial restart-delay 0 no fair-queue ! ! ip route 0.0.0.0 0.0.0.0 100.0.0.1 ! no ip http server no ip http secure-server ! ip nat inside source list 1 interface FastEthernet0/0 overload ! access-list 1 permit 192.168.2.0 0.0.0.255 access-list 101 permit ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255 ! FITEL#sho running.cfg ! ! FITELnet-F100 ! Firmware version: V02.07(02) 032307 ! ! ! ip route 0.0.0.0 0.0.0.0 100.0.0.2 ! access-list 1 permit 192.168.1.0 0.0.0.255 ! vpn enable vpnlog enable ! ipsec access-list 1 ipsec ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 ipsec access-list 64 bypass ip any any ipsec transform-set P2-des-md5 esp-des esp-md5-hmac ! service dhcp-server ! hostname FITEL ! ! ip dhcp pool lan1 exit ! interface ewan 1 crypto map kyoten ip address 100.0.0.1 255.255.255.0 ip nat inside source list 1 interface exit interface ewan 2 exit interface lan 1 ip address 192.168.1.254 255.255.255.0 exit ! ! crypto isakmp policy 1 authentication prekey encryption des group 1 hash md5 idtype-pre userfqdn key ascii secret lifetime 600 negotiation-mode main peer-identity address 100.0.0.2 exit crypto map kyoten 1 match address 1 set peer address 100.0.0.2 set transform-set P2-des-md5 exit crypto security-association exit ! end FITEL#sho cry isa sa [ 1] 100.0.0.2 <--> 100.0.0.1Main Mode UP pre-shared key DES MD5 Lifetime : 600secs Current : 527secs,1kbytes mcfg config-mode: off mcfg addr: off mcfg apl-version: IKE Keepalive: dpd ICMP Keepalive: off release on addr-change: off FITEL#sho cry ipsec sa IPSEC SA current insa : 1 current outsa : 1 [ 1] 192.168.2.0,255.255.255.0 ALL ALL <--> 192.168.1.0,255.255.255.0 ALL ALL peer: 100.0.0.2 -->UP ESP DES HMAC-MD5 PFS:off Lifetime: 600secs,4608000kbytes Anti-Replay: Enable O-SPI: 0x3b56eeb5 Current: 531secs,1kbytes out packet : 4 error packet : 0 I-SPI: 0x105e8a87 Current: 531secs,1kbytes in packet : 4 auth packet : 4 decrypt packet : 4 discard packet : 0 replay packet : 0 auth error packet : 0 FITEL#sho cry isakmp policy Protection suite priority [1] authentication method : preshared key encryption algorithm : DES - Data Encryption Standard (56 bit keys) Diffie-Hellman Group : #1 (768 bit) hash algorithm : Message Digest 5 lifetime : 600 seconds, no volume limit Disabled frequency : 0 Default protection suite authentication method : preshared key encryption algorithm : DES - Data Encryption Standard (56 bit keys) hash algorithm : Message Digest 5 Diffie-Hellman Group : #1 (768 bit) lifetime : 1000 seconds, no volume limit R1#sho cry isa sa dst src state conn-id slot status 100.0.0.1 100.0.0.2 QM_IDLE 1 0 ACTIVE R1#sho cry isa sa ? active Shows HA-enabled ISAKMP SAs in the active state detail Show ISAKMP SA Detail nat Show ISAKMP SA NAT Detail standby Shows HA-enabled ISAKMP SAs in the standby state vrf Show ISAKMP SA as per VRF | Output modifiers -->R1#sho cry isa sa det R1#sho cry isa sa detail Codes: C - IKE configuration mode, D - Dead Peer Detection K - Keepalives, N - NAT-traversal X - IKE Extended Authentication psk - Preshared key, rsig - RSA signature renc - RSA encryption C-id Local Remote I-VRF Status Encr Hash Auth DH Lifetime Cap. 1 100.0.0.2 100.0.0.1 ACTIVE des md5 psk 1 00:00:42 Connection-id:Engine-id = 1:1(software) R1# R1#sho cry ipsec sa interface: FastEthernet0/0 Crypto map tag: MAP1, local addr 100.0.0.2 protected vrf: (none) local ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0) current_peer 100.0.0.1 port 500 PERMIT, flags={origin_is_acl,} #pkts encaps: 4, #pkts encrypt: 4, #pkts digest: 4 #pkts decaps: 4, #pkts decrypt: 4, #pkts verify: 4 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0 #pkts not decompressed: 0, #pkts decompress failed: 0 #send errors 1, #recv errors 0 local crypto endpt.: 100.0.0.2, remote crypto endpt.: 100.0.0.1 path mtu 1500, ip mtu 1500, ip mtu idb FastEthernet0/0 current outbound spi: 0x105E8A87(274631303) inbound esp sas: spi: 0x3B56EEB5(995552949) transform: esp-des esp-md5-hmac , in use settings ={Tunnel, } conn id: 2001, flow_id: SW:1, crypto map: MAP1 sa timing: remaining key lifetime (k/sec): (4421774/438) IV size: 8 bytes replay detection support: Y Status: ACTIVE inbound ah sas: inbound pcp sas: outbound esp sas: spi: 0x105E8A87(274631303) transform: esp-des esp-md5-hmac , in use settings ={Tunnel, } conn id: 2002, flow_id: SW:2, crypto map: MAP1 sa timing: remaining key lifetime (k/sec): (4421774/437) IV size: 8 bytes replay detection support: Y Status: ACTIVE outbound ah sas: outbound pcp sas: R1#R1#sho cry isakmp policy Global IKE policy Protection suite of priority 1 encryption algorithm: DES - Data Encryption Standard (56 bit keys). hash algorithm: Message Digest 5 authentication method: Pre-Shared Key Diffie-Hellman group: #1 (768 bit) lifetime: 600 seconds, no volume limit Default protection suite encryption algorithm: DES - Data Encryption Standard (56 bit keys). hash algorithm: Secure Hash Standard authentication method: Rivest-Shamir-Adleman Signature Diffie-Hellman group: #1 (768 bit) lifetime: 86400 seconds, no volume limit R1#
続・IPsecをやってみる (FITELnet)
今度はfitelnetでやってみました。
PC1 ---- R1 ---- R2 ---- PC2
PC1: 192.168.1.13
R1: 192.168.1.254, 100.0.0.1
R2: 192.168.2.254, 100.0.0.2
PC2: 192.168.2.1
natあり
PC1 ---- R1 ---- R2 ---- PC2
PC1: 192.168.1.13
R1: 192.168.1.254, 100.0.0.1
R2: 192.168.2.254, 100.0.0.2
PC2: 192.168.2.1
natあり
R1#sho running.cfg ! ! FITELnet-F100 ! Firmware version: V02.07(02) 032307 ! ip route 0.0.0.0 0.0.0.0 ewan 1 ! access-list 1 permit 192.168.1.0 0.0.0.255 ! vpn enable vpnlog enable ! ipsec access-list 1 ipsec ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 ipsec access-list 64 bypass ip any any ipsec transform-set P2-des-md5 esp-des esp-md5-hmac ! service dhcp-server ! hostname R1 ! ip dhcp pool lan1 exit ! interface ewan 1 crypto map kyoten ip address 100.0.0.1 255.255.255.0 ip nat inside source list 1 interface exit interface ewan 2 exit interface lan 1 ip address 192.168.1.254 255.255.255.0 exit ! crypto isakmp policy 1 authentication prekey encryption des hash md5 idtype-pre userfqdn key ascii secret negotiation-mode main peer-identity address 100.0.0.2 exit crypto map kyoten 1 match address 1 set peer address 100.0.0.2 set transform-set P2-des-md5 exit ! end R2#sho running.cfg ! ! FITELnet-F100 ! Firmware version: V02.07(02) 032307 ! ip route 0.0.0.0 0.0.0.0 ewan 1 ip route 192.168.1.0 255.255.255.0 100.0.0.1 ! access-list 1 permit 192.168.2.0 0.0.0.255 ! vpn enable ! ipsec access-list 1 ipsec ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255 ipsec access-list 64 bypass ip any any ipsec transform-set P2-des-md5 esp-des esp-md5-hmac ! service dhcp-server ! hostname R2 ! ip dhcp pool lan1 exit ! interface ewan 1 crypto map center ip address 100.0.0.2 255.255.255.0 ip nat inside source list 1 interface exit interface ewan 2 exit interface lan 1 ip address 192.168.2.254 255.255.255.0 exit ! crypto isakmp policy 1 authentication prekey encryption des hash md5 idtype-pre userfqdn key ascii secret my-identity kyoten negotiation-mode main peer-identity address 100.0.0.1 exit crypto map center 1 match address 1 set peer address 100.0.0.1 set transform-set P2-des-md5 exit ! end R1#sho crypto isakmp sa [ 1] 100.0.0.2 <--> 100.0.0.1Main Mode UP pre-shared key DES MD5 Lifetime : 1000secs Current : 43secs,1kbytes mcfg config-mode: off mcfg addr: off mcfg apl-version: IKE Keepalive: dpd ICMP Keepalive: off release on addr-change: off R1#sho cry isakmp policy Protection suite priority [1] authentication method : preshared key encryption algorithm : DES - Data Encryption Standard (56 bit keys) hash algorithm : Message Digest 5 Disabled frequency : 0 Default protection suite authentication method : preshared key encryption algorithm : DES - Data Encryption Standard (56 bit keys) hash algorithm : Message Digest 5 Diffie-Hellman Group : #1 (768 bit) lifetime : 1000 seconds, no volume limit R1#sho crypto ipsec sa IPSEC SA current insa : 1 current outsa : 1 [ 1] 192.168.2.0,255.255.255.0 ALL ALL <--> 192.168.1.0,255.255.255.0 ALL ALL peer: 100.0.0.2 UP ESP DES HMAC-MD5 PFS:off Lifetime: 600secs Anti-Replay: Enable O-SPI: 0x2c159090 Current: 60secs,1kbytes out packet : 4 error packet : 0 I-SPI: 0x2b91a660 Current: 60secs,1kbytes in packet : 4 auth packet : 4 decrypt packet : 4 discard packet : 0 replay packet : 0 auth error packet : 0
2008/12/22
lhaで圧縮するのやめようぜ、もう・・・
さて・・・
MS Office 2000
Teraterm
Dynamips
IOSHunter
Lhaplus
Cygwin
などをインストールする。
lhaで圧縮するのやめようぜ、もう・・・。
SendToの場所
\Users\[ユーザー名]\AppData\Roaming\Microsoft\Windows\SendTo
MS Office 2000
Teraterm
Dynamips
IOSHunter
Lhaplus
Cygwin
などをインストールする。
lhaで圧縮するのやめようぜ、もう・・・。
SendToの場所
\Users\[ユーザー名]\AppData\Roaming\Microsoft\Windows\SendTo
2008/12/21
IPsecをやってみる (Dynamips)
Dynamipsは Vista64でも動いた。
ただし、フォルダが読み取り専用になっていたのでそれを直すのと、 telnetはデフォルトで無効になっている(クライアントも)ので有効にする必要がある。 IPsecをやってみます。
この設定だと、192.168.0/24 <---> 192.168.2.0/24 の通信が発生したときのみ、IPsec 通信が行われます。 --->
ただし、フォルダが読み取り専用になっていたのでそれを直すのと、 telnetはデフォルトで無効になっている(クライアントも)ので有効にする必要がある。 IPsecをやってみます。
192.168.1.0/24 10.10.10.0/24 192.168.2.0/24 +----+ +----+ +----+ +----+ | R3 +--------+ R1 +-------------+ R2 +--------+ R4 | +----+.2 .1+----+.1 .2+----+.1 .2+----+R1
R1#sho running-config Building configuration... Current configuration : 1695 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker ! no aaa new-model ip cef ! crypto isakmp policy 1 encr 3des hash md5 authentication pre-share lifetime 28800 crypto isakmp key cisco address 10.10.10.2 255.255.255.0 crypto isakmp keepalive 100 ! crypto ipsec transform-set IPSEC esp-3des esp-md5-hmac ! crypto map MAP1 1 ipsec-isakmp set peer 10.10.10.2 set transform-set IPSEC match address 101 interface FastEthernet0/0 ip address 192.168.1.1 255.255.255.0 duplex half speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 10.10.10.1 255.255.255.0 serial restart-delay 0 crypto map MAP1 ! interface Serial1/1 no ip address shutdown serial restart-delay 0 ! interface Serial1/2 no ip address shutdown serial restart-delay 0 ! interface Serial1/3 no ip address shutdown serial restart-delay 0 ! interface Serial1/4 no ip address shutdown serial restart-delay 0 ! interface Serial1/5 no ip address shutdown serial restart-delay 0 ! interface Serial1/6 no ip address shutdown serial restart-delay 0 ! interface Serial1/7 no ip address shutdown serial restart-delay 0 ! ip route 192.168.1.0 255.255.255.0 10.10.10.2 ip route 192.168.2.0 255.255.255.0 10.10.10.2 ! no ip http server no ip http secure-server ! access-list 101 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 ! control-plane ! gatekeeper shutdown ! line con 0 stopbits 1 line aux 0 stopbits 1 line vty 0 4 login ! end R2 R2#sho running-config Building configuration... Current configuration : 1710 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R2 ! boot-start-marker boot-end-marker ! no aaa new-model ! ip cef ! crypto isakmp policy 1 encr 3des hash md5 authentication pre-share lifetime 28800 crypto isakmp key cisco address 10.10.10.1 255.255.255.0 crypto isakmp keepalive 100 ! crypto ipsec transform-set IPSEC esp-3des esp-md5-hmac ! crypto map MAP1 1 ipsec-isakmp set peer 10.10.10.1 set transform-set IPSEC match address 101 ! interface FastEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex half speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0 ip address 10.10.10.2 255.255.255.0 serial restart-delay 0 no fair-queue crypto map MAP1 ! interface Serial1/1 no ip address shutdown serial restart-delay 0 ! interface Serial1/2 no ip address shutdown serial restart-delay 0 ! interface Serial1/3 no ip address shutdown serial restart-delay 0 ! interface Serial1/4 no ip address shutdown serial restart-delay 0 ! interface Serial1/5 no ip address shutdown serial restart-delay 0 ! interface Serial1/6 no ip address shutdown serial restart-delay 0 ! interface Serial1/7 no ip address shutdown serial restart-delay 0 ! ip route 192.168.1.0 255.255.255.0 10.10.10.1 ip route 192.168.2.0 255.255.255.0 10.10.10.1 ! no ip http server no ip http secure-server ! access-list 101 permit ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255 ! control-plane ! gatekeeper shutdown line con 0 stopbits 1 line aux 0 stopbits 1 line vty 0 4 login end R3 R3#sho running-config Building configuration... Current configuration : 621 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R3 ! boot-start-marker boot-end-marker ! no aaa new-model ! ip cef ! interface FastEthernet0/0 ip address 192.168.1.2 255.255.255.0 duplex auto speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! ip route 0.0.0.0 0.0.0.0 192.168.1.1 ! no ip http server no ip http secure-server ! control-plane ! gatekeeper shutdown ! line con 0 stopbits 1 line aux 0 line vty 0 4 ! end R4 R4#sho running-config Building configuration... Current configuration : 621 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R4 ! boot-start-marker boot-end-marker ! no aaa new-model ! ip cef ! interface FastEthernet0/0 ip address 192.168.2.2 255.255.255.0 duplex auto speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! ip route 0.0.0.0 0.0.0.0 192.168.2.1 ! no ip http server no ip http secure-server ! control-plane ! gatekeeper shutdown ! line con 0 stopbits 1 line aux 0 line vty 0 4 ! end設定しただけではIPsec SAは確立しません。
この設定だと、192.168.0/24 <---> 192.168.2.0/24 の通信が発生したときのみ、IPsec 通信が行われます。 --->
R3#ping 192.168.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 220/260/356 ms
R3#
R1#show crypto isakmp sa
dst src state conn-id slot status
10.10.10.2 10.10.10.1 QM_IDLE 1 0 ACTIVE
R1#
R1#sho crypto isakmp peers
Peer: 10.10.10.2 Port: 500 Local: 10.10.10.1
Phase1 id: 10.10.10.2
R1#
R1#sho crypto isakmp policy
Global IKE policy
Protection suite of priority 1
encryption algorithm: Three key triple DES
hash algorithm: Message Digest 5
authentication method: Pre-Shared Key
Diffie-Hellman group: #1 (768 bit)
lifetime: 28800 seconds, no volume limit
Default protection suite
encryption algorithm: DES - Data Encryption Standard (56 bit keys).
hash algorithm: Secure Hash Standard
authentication method: Rivest-Shamir-Adleman Signature
Diffie-Hellman group: #1 (768 bit)
lifetime: 86400 seconds, no volume limit
R1#
08/12/22(Mon) 08:36
R1#sho cry ipsec sa
interface: Serial1/0
Crypto map tag: MAP1, local addr 10.10.10.1
protected vrf: (none)
local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
current_peer 10.10.10.2 port 500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 18, #pkts encrypt: 18, #pkts digest: 18
#pkts decaps: 17, #pkts decrypt: 17, #pkts verify: 17
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0
#pkts not decompressed: 0, #pkts decompress failed: 0
#send errors 2, #recv errors 0
local crypto endpt.: 10.10.10.1, remote crypto endpt.: 10.10.10.2
path mtu 1500, ip mtu 1500, ip mtu idb Serial1/0
current outbound spi: 0x193624A0(422978720)
inbound esp sas:
spi: 0xC5E6FB2A(3320249130)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel, }
conn id: 2001, flow_id: SW:1, crypto map: MAP1
sa timing: remaining key lifetime (k/sec): (4482477/2342)
IV size: 8 bytes
replay detection support: Y
Status: ACTIVE
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0x193624A0(422978720)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel, }
conn id: 2002, flow_id: SW:2, crypto map: MAP1
sa timing: remaining key lifetime (k/sec): (4482477/2341)
IV size: 8 bytes
replay detection support: Y
Status: ACTIVE
outbound ah sas:
outbound pcp sas:
R1#
R1#sho cry ipsec transform-set
Transform set IPSEC: { esp-3des esp-md5-hmac }
will negotiate = { Tunnel, },
R1#sho cry ipsec ?
policy Show IPSEC client policies
profile Show ipsec profile information
sa IPSEC SA table
security-association Show parameters for IPSec security associations
transform-set Crypto transform sets
R1#sho cry ipsec se
R1#sho cry ipsec security-association
Security association lifetime: 4608000 kilobytes/3600 seconds
R1の S1/0をキャプチャしてみると、ISAKMP Identity Protectionが3往復、ISAKMP Quick Modeが1往復半した後に、ESPパケットの通信が開始されている。
これは vista ultimate 64bitバージョンで、Dynamipsを使って4台の7200をエミュレートしたものである。
このとき、teratermのログを保存したのだが、そのファイルが見つからなくなった。
しかし、teratermでログを保存するメニューを出すと、ちゃんとファイルが表示される。
と、エクスプローラのメニューに「互換性ファイル」という文字が。
そこをクリックすると表示された。しかし今度は他のファイルが見えなくなる。
エクスプローラをいったん閉じて、再び開くと、またログファイル以外が見える。
この「互換性ファイル」問題は、bitcometを使ったときに出くわしたのだが、
いまだに意味がよくわからない。
まあ、スレ違いの話題なので、これについてはまたの機会に。