このブログを検索

ラベル motion の投稿を表示しています。 すべての投稿を表示
ラベル motion の投稿を表示しています。 すべての投稿を表示

2026/03/18

raspi zero2 でカメラモジュール

pi zero2になったからなのか、OSが新しくなったからなのか、その両方か、あるいはカメラモジュールのバージョンのせいか、カメラの扱い方が変わった。

昔は、

vcgencmd get_camera

とかやったのだけど、今はこれをやっても認識されない。(認識されているかがわからない)

raspi-configで、legacy cameraを有効にする、というオプションがあったこともあったが、昨日(2026/3)インストールしたOSではそれがない。

たしかlibcameraモジュールというのを使うようになったはず。

....

libcameraも使わなくなったようだ。

コロコロ変えるなよ....

# rpicam-

rpicam-hello  rpicam-jpeg   rpicam-raw    rpicam-still  rpicam-vid


とりあえずこれで写真は撮れた。

# rpicam-jpeg --output test.jpg


さて、これを私の大好きなmotionで使うには....


# apt install libcamera-tools libcamera-v4l2


で、

libcamerify motion -b

で動いた。


ちなみに今は起動時にmotionが自動起動するようになっている。

そしてlibcamerifyで起動しないようになっているから

sudo systemctl edit motion

をやって、以下を書く。

[Service]

ExecStart=
ExecStart=/usr/bin/libcamerify /usr/bin/motion


copilotに聞きながらやった。

2025/02/02

motionが動かなくなる

raspberry pi zero2 + camera module v3(Wide)

で動かしていたmotionにアクセスできない。

再起動してもダメ。

libcameraコマンドで静止画も動画も撮れるのでカメラを認識していないとか壊れたとかではない。

motionの設定か。そもそも何も変えてないはずなんだけど。

libcamerify motion -b

を実行すると、特にどこにもエラーは出ていないようだが、motionが起動しない。

最近、別のことをやっていてraspberry piから遠ざかっていた。

後でなんか思いついたら試してみる。


2024/11/05

Raspberry Pi zeroのライブカメラの首振り

pi zeroにカメラをつけてケースに収めたものにサーボモーター(SG92R)をくっつけて、本体ごと回転させてカメラを首振りさせてみた。

pythonのソース

#!/usr/bin/python
import pigpio
import time
gpio_pwm = 18
pig = pigpio.pi()
pig.set_mode(gpio_pwm, pigpio.OUTPUT)

para_max = 110000
para_min = 70000
para = para_min
interval=20
delta=10000

try:
  while True:
    if para >= para_max:
        flag=-1
    elif para <= para_min:
        flag=1
    para = para + (delta*flag)
    pig.hardware_PWM(gpio_pwm, 50, para)
    time.sleep(interval)
except KeyboardInterrupt:
  pig.set_mode(gpio_pwm, pigpio.INPUT)
  pig.stop()



Piとの接続は、SG924Rの茶→GND、赤→5V、オレンジ→GPIO18

これを実行するためには pi gpio daemonが起動している必要がある。

sudo pigpiod

そして、motionをバックグラウンドで動かしておく。

libcamerify motion -b


このやり方はPWM制御といってduty比というものを指定する。

hardware_PWM に3つの引数を渡しているが順にGPIOのピン番号(今回は18を使用)、動作周波数(50Hz)、duty比である。

動作周波数はモータによるようだ。SG92RのデータシートがみつからないのだがSG90Rはあって、そこに50Hzと書いてあった。

duty比が大きいと大きく回転することはわかったがどこが基準でどれだけ大きくするとどれだけ回転するのかがいまいちよくわからない。

誰かのソースを動かしてみて、値を変えながら確認していった。

モーターをpi zeroのケースの下にくっつけたのだがその時の角度はテキトーである。

duty比は70000~110000の範囲で変えると、正確に測っていないが大体120度くらいの範囲で首振りできた。

初期値を70000にして、大きくしていくと半時計周りに回転する。そして11000を超えたら、こんどは小さくしていくと時計回りに回転する。70000を下回ったらまた大きくする。これを繰り返して「首振り」動作が実現できた。

モータを回してsleepする時間と、duty比の変化量を変えることでゆっくり首振りしたり、なめらかにさせたり、ガクンガクンと大幅に首振りさせることができる。


電源ケーブルやgpioと接続しているケーブルが邪魔にならないように余裕をもたせてたるみをもたせつつ固定しておく。ある程度重みのある台となるものにモーターを固定しpi zeroのケースをつけた。

仮なので両面テープやビニールテープを使っている。




2023/01/05

motionでカメラを二つ使う

 motion4.3.2

root@raspberrypi:/etc/motion# cat /etc/os-release

PRETTY_NAME="Raspbian GNU/Linux 11 (bullseye)"

(略)


よくわからなかったのでメモ。


motion.confの下の方に、以下のような設定があり、コメントアウトされている。


##############################################################

# Camera config files - One for each camera.

##############################################################

; camera /usr/etc/motion/camera1.conf

; camera /usr/etc/motion/camera2.conf

; camera /usr/etc/motion/camera3.conf

; camera /usr/etc/motion/camera4.conf


カメラを2台使うなら、最初の2行をコメントアウトして、設定ファイルを置けばよい。

camera~ のところは、以前は thread~ だったが、変わったようだ。


設定ファイルに記載するのは、2台のカメラ固有の設定のみでよい。
それ以外の設定は motion.confの内容が使われるようだ。


以下、サンプル。

設定ファイルの場所と名前は変えた。

camera0がraspiカメラで、camera1が外付けのUSBカメラ。
筐体を横にしたので、camera0だけ rotate 270を設定した。

##############################################################

# Camera config files - One for each camera.

##############################################################

camera /etc/motion/camera0.conf

camera /etc/motion/camera1.conf

; camera /usr/etc/motion/camera3.conf

; camera /usr/etc/motion/camera4.conf


#camera0.conf

# Video device (e.g. /dev/video0) to be used for capturing.
videodevice /dev/video0

# Image width in pixels.
width 800

# Image height in pixels.
height 600

# Maximum number of frames to be captured per second.
framerate 5

# Text to be overlayed in the lower left corner of images
text_left CAMERA0

# Text to be overlayed in the lower right corner of images.
text_right %Y-%m-%d\n%T-%q

norm 1

rotate 270


#camera1.conf

# Video device (e.g. /dev/video0) to be used for capturing.
videodevice /dev/video1

# Image width in pixels.
width 800

# Image height in pixels.
height 600

# Maximum number of frames to be captured per second.
framerate 5

# Text to be overlayed in the lower left corner of images
text_left CAMERA1

# Text to be overlayed in the lower right corner of images.
text_right %Y-%m-%d\n%T-%q

norm 1


本家のヘルプページ

2022/02/18

2022年のmotion@raspberry pi

しばらく放置していたraspberry piを起動して、最近変えた構成に合わせようとして

/etc/dhcpcd.conf のgatewayのアドレスを変更しようとしたら、なんど変更しても再起動すると元に戻ってしまう。

networkingがresolve.confを書き換えるとかいうことはあるようだがdhcpd.confが何かによって上書きされるという話は聞いたことがない。

どこかのフォーラムで同じようなケースがありsdカードの不良じゃないかみたいな結論になっていた。

私もそれしかないと思い新しいSDカードにインストールしなおした。

まあ、私のraspberry piには大した設定は入っていないので再インストールすることはそんなにオオゴトではない。


ただ、久しぶり、といっても1年とか2年とかだが、にインストールしたらちょこちょこと変化があった。

osを書き込むソフトが新しいものになりフォーマットもせずにいきなり書き込めた。

初期状態ではコンソールもsshもアクセスできない。(まあこれは少し前に気づいていたこと)。

それから、カメラモジュールがlegacy扱いされていた。

raspistillコマンドがなくなりlibcamera-still とかいうコマンドになった。

(OSによるのか)

が、libcamera-stillは、先ほどのlegacy cameraが有効になっていると使えない。

そしてlegacy cameraを無効にするとmotionでcameraがdetectされない。

なので、legacyカメラを有効にし、コマンドでのカメラ動作確認はせずにmotionを動かして確認する。


前から使っているmotionをインストールした。

motion.confは

norm 1 を追加

stream_localhost off

正常動作を確認したら、daemon on にする


自分の以前書いたメモに以下の記述があったのでそれもやったが必要かどうかは微妙

> /etc/modulesに以下の記述を追加

>bcm2835-v4l2


とりあえず動いている。


pi@raspberrypi:~ $ cat /etc/debian_version
11.2

pi@raspberrypi:~ $ cat /etc/issue
Debian GNU/Linux 11 \n \l


pi@raspberrypi:~ $ lsb_release -a
No LSB modules are available.
Distributor ID: Debian
Description:    Debian GNU/Linux 11 (bullseye)
Release:        11
Codename:       bullseye

pi@raspberrypi:~ $ uname -a
Linux raspberrypi 5.10.92-v8+ #1514 SMP PREEMPT Mon Jan 17 17:39:38 GMT 2022 aarch64 GNU/Linux

2019/08/06

motion 4.1.1 デフォルトコンフィグ

pi@raspberrypi:~ $ sudo cat /etec/motion/motion.conf
# Rename this distribution example file to motion.conf
#
# This config file was generated by motion 4.1.1
# Documentation:  /usr/share/doc/motion/motion_guide.html

############################################################
# Daemon
############################################################

# Start in daemon (background) mode and release terminal (default: off)
daemon off

# File to store the process ID, also called pid file. (default: not defined)
process_id_file /var/run/motion/motion.pid

############################################################
# Basic Setup Mode
############################################################

# Start in Setup-Mode, daemon disabled. (default: off)
setup_mode off


# Use a file to save logs messages, if not defined stderr and syslog is used. (default: not defined)
logfile /var/log/motion/motion.log

# Level of log messages [1..9] (EMG, ALR, CRT, ERR, WRN, NTC, INF, DBG, ALL). (default: 6 / NTC)
log_level 6

# Filter to log messages by type (COR, STR, ENC, NET, DBL, EVT, TRK, VID, ALL). (default: ALL)
log_type all

###########################################################
# Capture device options
############################################################

# Videodevice to be used for capturing  (default /dev/video0)
# for FreeBSD default is /dev/bktr0
videodevice /dev/video0

# v4l2_palette allows one to choose preferable palette to be use by motion
# See motion_guide.html for the valid options and values.  (default: 17)
v4l2_palette 17

# Tuner device to be used for capturing using tuner as source (default /dev/tuner0)
# This is ONLY used for FreeBSD. Leave it commented out for Linux
; tunerdevice /dev/tuner0

# The video input to be used (default: -1)
# Should normally be set to 0 or 1 for video/TV cards, and -1 for USB cameras
# Set to 0 for uvideo(4) on OpenBSD
input -1

# The video norm to use (only for video capture and TV tuner cards)
# Values: 0 (PAL), 1 (NTSC), 2 (SECAM), 3 (PAL NC no colour). Default: 0 (PAL)
norm 0

# The frequency to set the tuner to (kHz) (only for TV tuner cards) (default: 0)
frequency 0

# Override the power line frequency for the webcam. (normally not necessary)
# Values:
# -1 : Do not modify device setting
# 0  : Power line frequency Disabled
# 1  : 50hz
# 2  : 60hz
# 3  : Auto
power_line_frequency -1

# Rotate image this number of degrees. The rotation affects all saved images as
# well as movies. Valid values: 0 (default = no rotation), 90, 180 and 270.
rotate 0

# Flip image over a given axis (vertical or horizontal), vertical means from left to right
# horizontal means top to bottom. Valid values: none, v and h.
flip_axis none

# Image width (pixels). Valid range: Camera dependent, default: 320
width 320

# Image height (pixels). Valid range: Camera dependent, default: 240
height 240

# Maximum number of frames to be captured per second.
# Valid range: 2-100. Default: 100 (almost no limit).
framerate 2

# Minimum time in seconds between capturing picture frames from the camera.
# Default: 0 = disabled - the capture rate is given by the camera framerate.
# This option is used when you want to capture images at a rate lower than 2 per second.
minimum_frame_time 0

# Full Network Camera URL.  Valid Services: http:// ftp:// mjpg:// rtsp:// mjpeg:// file:// rtmp://
; netcam_url value

# Username and password for network camera if required. Syntax is user:password
; netcam_userpass value

# The setting for keep-alive of network socket, should improve performance on compatible net cameras.
# off:   The historical implementation using HTTP/1.0, closing the socket after each http request.
# force: Use HTTP/1.0 requests with keep alive header to reuse the same connection.
# on:    Use HTTP/1.1 requests that support keep alive as default.
# Default: off
netcam_keepalive off

# URL to use for a netcam proxy server, if required, e.g. "http://myproxy".
# If a port number other than 80 is needed, use "http://myproxy:1234".
# Default: not defined
; netcam_proxy value

# Set less strict jpeg checks for network cameras with a poor/buggy firmware.
# Default: off
netcam_tolerant_check off

# RTSP connection uses TCP to communicate to the camera. Can prevent image corruption.
# Default: on
rtsp_uses_tcp on

# Name of camera to use if you are using a camera accessed through OpenMax/MMAL
# Default: Not defined
; mmalcam_name vc.ril.camera

# Camera control parameters (see raspivid/raspistill tool documentation)
# Default: Not defined
; mmalcam_control_params -hf

# Let motion regulate the brightness of a video device (default: off).
# The auto_brightness feature uses the brightness option as its target value.
# If brightness is zero auto_brightness will adjust to average brightness value 128.
# Only recommended for cameras without auto brightness
auto_brightness off

# Set the initial brightness of a video device.
# If auto_brightness is enabled, this value defines the average brightness level
# which Motion will try and adjust to.
# Valid range 0-255, default 0 = disabled
brightness 0

# Set the contrast of a video device.
# Valid range 0-255, default 0 = disabled
contrast 0

# Set the saturation of a video device.
# Valid range 0-255, default 0 = disabled
saturation 0

# Set the hue of a video device (NTSC feature).
# Valid range 0-255, default 0 = disabled
hue 0


############################################################
# Round Robin (multiple inputs on same video device name)
############################################################

# Number of frames to capture in each roundrobin step (default: 1)
roundrobin_frames 1

# Number of frames to skip before each roundrobin step (default: 1)
roundrobin_skip 1

# Try to filter out noise generated by roundrobin (default: off)
switchfilter off


############################################################
# Motion Detection Settings:
############################################################

# Threshold for number of changed pixels in an image that
# triggers motion detection (default: 1500)
threshold 1500

# Automatically tune the threshold down if possible (default: off)
threshold_tune off

# Noise threshold for the motion detection (default: 32)
noise_level 32

# Automatically tune the noise threshold (default: on)
noise_tune on

# Despeckle motion image using (e)rode or (d)ilate or (l)abel (Default: not defined)
# Recommended value is EedDl. Any combination (and number of) of E, e, d, and D is valid.
# (l)abeling must only be used once and the 'l' must be the last letter.
# Comment out to disable
despeckle_filter EedDl

# Detect motion in predefined areas (1 - 9). Areas are numbered like that:  1 2 3
# A script (on_area_detected) is started immediately when motion is         4 5 6
# detected in one of the given areas, but only once during an event.        7 8 9
# One or more areas can be specified with this option. Take care: This option
# does NOT restrict detection to these areas! (Default: not defined)
; area_detect value

# PGM file to use as a sensitivity mask.
# Full path name to. (Default: not defined)
; mask_file value

# PGM file to completely mask out a area of image.
# Full path name to. (Default: not defined)
# mask_privacy value

# Dynamically create a mask file during operation (default: 0)
# Adjust speed of mask changes from 0 (off) to 10 (fast)
smart_mask_speed 0

# Ignore sudden massive light intensity changes given as a percentage of the picture
# area that changed intensity. Valid range: 0 - 100 , default: 0 = disabled
lightswitch 0

# Picture frames must contain motion at least the specified number of frames
# in a row before they are detected as true motion. At the default of 1, all
# motion is detected. Valid range: 1 to thousands, recommended 1-5
minimum_motion_frames 1

# Specifies the number of pre-captured (buffered) pictures from before motion
# was detected that will be output at motion detection.
# Recommended range: 0 to 5 (default: 0)
# Do not use large values! Large values will cause Motion to skip video frames and
# cause unsmooth movies. To smooth movies use larger values of post_capture instead.
pre_capture 0

# Number of frames to capture after motion is no longer detected (default: 0)
post_capture 0

# Event Gap is the seconds of no motion detection that triggers the end of an event.
# An event is defined as a series of motion images taken within a short timeframe.
# Recommended value is 60 seconds (Default). The value -1 is allowed and disables
# events causing all Motion to be written to one single movie file and no pre_capture.
# If set to 0, motion is running in gapless mode. Movies don't have gaps anymore. An
# event ends right after no more motion is detected and post_capture is over.
event_gap 60

# Maximum length in seconds of a movie
# When value is exceeded a new movie file is created. (Default: 0 = infinite)
max_movie_time 0

# Always save images even if there was no motion (default: off)
emulate_motion off


############################################################
# Image File Output
############################################################

# Output 'normal' pictures when motion is detected (default: off)
# Valid values: on, off, first, best, center
# When set to 'first', only the first picture of an event is saved.
# Picture with most motion of an event is saved when set to 'best'.
# Picture with motion nearest center of picture is saved when set to 'center'.
# Can be used as preview shot for the corresponding movie.
output_pictures off

# Output pictures with only the pixels moving object (ghost images) (default: off)
output_debug_pictures off

# The quality (in percent) to be used by the jpeg and webp compression (default: 75)
quality 75

# Type of output images
# Valid values: jpeg, ppm or webp (default: jpeg)
picture_type jpeg

############################################################

# Use ffmpeg to encode videos of motion (default: off)
ffmpeg_output_movies on

# Use ffmpeg to make videos showing the moving pixels (ghost images) (default: off)
ffmpeg_output_debug_movies off

# Bitrate to be used by the ffmpeg encoder (default: 400000)
# This option is ignored if ffmpeg_variable_bitrate is not 0 (disabled)
ffmpeg_bps 400000

# Enables and defines variable bitrate for the ffmpeg encoder.
# ffmpeg_bps is ignored if variable bitrate is enabled.
# Valid values: 0 (default) = fixed bitrate defined by ffmpeg_bps,
# or the range 1 - 100 where 1 means worst quality and 100 is best.
ffmpeg_variable_bitrate 0

# Container/Codec output videos
# Valid values: mpeg4, msmpeg4, swf,flv, ffv1, mov, mp4, mkv, hevc
ffmpeg_video_codec mkv

# When creating videos, should frames be duplicated in order
# to keep up with the requested frames per second
# (default: true)
ffmpeg_duplicate_frames true

# Interval in seconds between timelapse captures.  Default: 0 = off
timelapse_interval 0

# Timelapse file rollover mode. See motion_guide.html for options and uses.
timelapse_mode daily

# Frame rate for timelapse playback
timelapse_fps 30

# Container/Codec for timelapse video. Valid values: mpg or mpeg4
timelapse_codec mpg

############################################################
# External pipe to video encoder
# Replacement for FFMPEG builtin encoder for ffmpeg_output_movies only.
# The options movie_filename and timelapse_filename are also used
# by the ffmpeg feature
#############################################################

# Bool to enable or disable extpipe (default: off)
use_extpipe off

# External program (full path and opts) to pipe raw video to
# Generally, use '-' for STDIN...
;extpipe mencoder -demuxer rawvideo -rawvideo w=%w:h=%h:i420 -ovc x264 -x264encopts bframes=4:frameref=1:subq=1:scenecut=-1:nob_adapt:threads=1:keyint=1000:8x8dct:vbv_bufsize=4000:crf=24:partitions=i8x8,i4x4:vbv_maxrate=800:no-chroma-me -vf denoise3d=16:12:48:4,pp=lb -of   avi -o %f.avi - -fps %fps
;extpipe x264 - --input-res %wx%h --fps %fps --bitrate 2000 --preset ultrafast --quiet -o %f.mp4
;extpipe mencoder -demuxer rawvideo -rawvideo w=%w:h=%h:fps=%fps -ovc x264 -x264encopts preset=ultrafast -of lavf -o %f.mp4 - -fps %fps
;extpipe ffmpeg -y -f rawvideo -pix_fmt yuv420p -video_size %wx%h -framerate %fps -i pipe:0 -vcodec libx264 -preset ultrafast -f mp4 %f.mp4


############################################################
# Snapshots (Traditional Periodic Webcam File Output)
############################################################

# Make automated snapshot every N seconds (default: 0 = disabled)
snapshot_interval 0


############################################################
# Text Display
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second, %T = HH:MM:SS,
# %v = event, %q = frame number, %t = camera id number,
# %D = changed pixels, %N = noise level, \n = new line,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
# %C = value defined by text_event - do not use with text_event!
# You can put quotation marks around the text to allow
# leading spaces
############################################################

# Locate and draw a box around the moving object.
# Valid values: on, off, preview (default: off)
# Set to 'preview' will only draw a box in preview_shot pictures.
locate_motion_mode off

# Set the look and style of the locate box if enabled.
# Valid values: box, redbox, cross, redcross (default: box)
# Set to 'box' will draw the traditional box.
# Set to 'redbox' will draw a red box.
# Set to 'cross' will draw a little cross to mark center.
# Set to 'redcross' will draw a little red cross to mark center.
locate_motion_style box

# Draws the timestamp using same options as C function strftime(3)
# Default: %Y-%m-%d\n%T = date in ISO format and time in 24 hour clock
# Text is placed in lower right corner
text_right %Y-%m-%d\n%T-%q

# Draw a user defined text on the images using same options as C function strftime(3)
# Default: Not defined = no text
# Text is placed in lower left corner
; text_left CAMERA %t

# Draw the number of changed pixed on the images (default: off)
# Will normally be set to off except when you setup and adjust the motion settings
# Text is placed in upper right corner
text_changes off

# This option defines the value of the special event conversion specifier %C
# You can use any conversion specifier in this option except %C. Date and time
# values are from the timestamp of the first image in the current event.
# Default: %Y%m%d%H%M%S
# The idea is that %C can be used filenames and text_left/right for creating
# a unique identifier for each event.
text_event %Y%m%d%H%M%S

# Draw characters at twice normal size on images. (default: off)
text_double off


# Text to include in a JPEG EXIF comment
# May be any text, including conversion specifiers.
# The EXIF timestamp is included independent of this text.
;exif_text %i%J/%K%L

############################################################
# Target Directories and filenames For Images And Films
# For the options snapshot_, picture_, movie_ and timelapse_filename
# you can use conversion specifiers
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second,
# %v = event, %q = frame number, %t = camera id number,
# %D = changed pixels, %N = noise level,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
# %C = value defined by text_event
# Quotation marks round string are allowed.
############################################################

# Target base directory for pictures and films
# Recommended to use absolute path. (Default: current working directory)
target_dir /var/lib/motion

# File path for snapshots (jpeg, ppm or webp) relative to target_dir
# Default: %v-%Y%m%d%H%M%S-snapshot
# Default value is equivalent to legacy oldlayout option
# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-snapshot
# File extension .jpg, .ppm or .webp is automatically added so do not include this.
# Note: A symbolic link called lastsnap.jpg created in the target_dir will always
# point to the latest snapshot, unless snapshot_filename is exactly 'lastsnap'
snapshot_filename %v-%Y%m%d%H%M%S-snapshot

# File path for motion triggered images (jpeg, ppm or .webp) relative to target_dir
# Default: %v-%Y%m%d%H%M%S-%q
# Default value is equivalent to legacy oldlayout option
# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-%q
# File extension .jpg, .ppm or .webp is automatically added so do not include this
# Set to 'preview' together with best-preview feature enables special naming
# convention for preview shots. See motion guide for details
picture_filename %v-%Y%m%d%H%M%S-%q

# File path for motion triggered ffmpeg films (movies) relative to target_dir
# Default: %v-%Y%m%d%H%M%S
# File extensions(.mpg .avi) are automatically added so do not include them
movie_filename %v-%Y%m%d%H%M%S

# File path for timelapse movies relative to target_dir
# Default: %Y%m%d-timelapse
# File extensions(.mpg .avi) are automatically added so do not include them
timelapse_filename %Y%m%d-timelapse

############################################################
# Global Network Options
############################################################
# Enable IPv6 (default: off)
ipv6_enabled off

############################################################
# Live Stream Server
############################################################

# The mini-http server listens to this port for requests (default: 0 = disabled)
stream_port 8081

# 50% scaled down substream (default: 0 = disabled)
# substream_port 8082

# Quality of the jpeg (in percent) images produced (default: 50)
stream_quality 50

# Output frames at 1 fps when no motion is detected and increase to the
# rate given by stream_maxrate when motion is detected (default: off)
stream_motion off

# Maximum framerate for stream streams (default: 1)
stream_maxrate 1

# Restrict stream connections to localhost only (default: on)
stream_localhost on

# Limits the number of images per connection (default: 0 = unlimited)
# Number can be defined by multiplying actual stream rate by desired number of seconds
# Actual stream rate is the smallest of the numbers framerate and stream_maxrate
stream_limit 0

# Set the authentication method (default: 0)
# 0 = disabled
# 1 = Basic authentication
# 2 = MD5 digest (the safer authentication)
stream_auth_method 0

# Authentication for the stream. Syntax username:password
# Default: not defined (Disabled)
; stream_authentication username:password

# Percentage to scale the stream image for preview
# This is scaled on the browser side, motion will keep sending full frames
# Default: 25
; stream_preview_scale 25

# Have stream preview image start on a new line
# Default: no
; stream_preview_newline no

############################################################
# HTTP Based Control
############################################################

# TCP/IP port for the http server to listen on (default: 0 = disabled)
webcontrol_port 8080

# Restrict control connections to localhost only (default: on)
webcontrol_localhost on

# Output for http server, select off to choose raw text plain (default: on)
webcontrol_html_output on

# Authentication for the http based control. Syntax username:password
# Default: not defined (Disabled)
; webcontrol_authentication username:password

# Parameters to include on webcontrol.  0=none, 1=limited, 2=advanced, 3=restricted
# Default: 0 (none)
webcontrol_parms 0


############################################################
# Tracking (Pan/Tilt)
#############################################################

# Type of tracker (0=none (default), 1=stepper, 2=iomojo, 3=pwc, 4=generic, 5=uvcvideo, 6=servo)
# The generic type enables the definition of motion center and motion size to
# be used with the conversion specifiers for options like on_motion_detected
track_type 0

# Enable auto tracking (default: off)
track_auto off

# Serial port of motor (default: none)
;track_port /dev/ttyS0

# Motor number for x-axis (default: 0)
;track_motorx 0

# Set motorx reverse (default: 0)
;track_motorx_reverse 0

# Motor number for y-axis (default: 0)
;track_motory 1

# Set motory reverse (default: 0)
;track_motory_reverse 0

# Maximum value on x-axis (default: 0)
;track_maxx 200

# Minimum value on x-axis (default: 0)
;track_minx 50

# Maximum value on y-axis (default: 0)
;track_maxy 200

# Minimum value on y-axis (default: 0)
;track_miny 50

# Center value on x-axis (default: 0)
;track_homex 128

# Center value on y-axis (default: 0)
;track_homey 128

# ID of an iomojo camera if used (default: 0)
track_iomojo_id 0

# Angle in degrees the camera moves per step on the X-axis
# with auto-track (default: 10)
# Currently only used with pwc type cameras
track_step_angle_x 10

# Angle in degrees the camera moves per step on the Y-axis
# with auto-track (default: 10)
# Currently only used with pwc type cameras
track_step_angle_y 10

# Delay to wait for after tracking movement as number
# of picture frames (default: 10)
track_move_wait 10

# Speed to set the motor to (stepper motor option) (default: 255)
track_speed 255

# Number of steps to make (stepper motor option) (default: 40)
track_stepsize 40


############################################################
# External Commands, Warnings and Logging:
# You can use conversion specifiers for the on_xxxx commands
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second,
# %v = event, %q = frame number, %t = camera id number,
# %D = changed pixels, %N = noise level,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
# %C = value defined by text_event
# %f = filename with full path
# %n = number indicating filetype
# Both %f and %n are only defined for on_picture_save,
# on_movie_start and on_movie_end
# Quotation marks round string are allowed.
############################################################

# Do not sound beeps when detecting motion (default: on)
# Note: Motion never beeps when running in daemon mode.
quiet on

# Command to be executed when an event starts. (default: none)
# An event starts at first motion detected after a period of no motion defined by event_gap
; on_event_start value

# Command to be executed when an event ends after a period of no motion
# (default: none). The period of no motion is defined by option event_gap.
; on_event_end value

# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
# To give the filename as an argument to a command append it with %f
; on_picture_save value

# Command to be executed when a motion frame is detected (default: none)
; on_motion_detected value

# Command to be executed when motion in a predefined area is detected
# Check option 'area_detect'.   (default: none)
; on_area_detected value

# Command to be executed when a movie file (.mpg|.avi) is created. (default: none)
# To give the filename as an argument to a command append it with %f
; on_movie_start value

# Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
# To give the filename as an argument to a command append it with %f
; on_movie_end value

# Command to be executed when a camera can't be opened or if it is lost
# NOTE: There is situations when motion don't detect a lost camera!
# It depends on the driver, some drivers dosn't detect a lost camera at all
# Some hangs the motion thread. Some even hangs the PC! (default: none)
; on_camera_lost value

# Command to be executed when a camera that was lost has been found (default: none)
# NOTE: If motion doesn't properly detect a lost camera, it also won't know it found one.
; on_camera_found value

#####################################################################
# Common Options for database features.
# Options require database options to be active also.
#####################################################################

# Log to the database when creating motion triggered picture file  (default: on)
; sql_log_picture on

# Log to the database when creating a snapshot image file (default: on)
; sql_log_snapshot on

# Log to the database when creating motion triggered movie file (default: off)
; sql_log_movie off

# Log to the database when creating timelapse movies file (default: off)
; sql_log_timelapse off

# SQL query string that is sent to the database
# Use same conversion specifiers has for text features
# Additional special conversion specifiers are
# %n = the number representing the file_type
# %f = filename with full path
# Default value:
# Create tables :
##
# Mysql
# CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp(14), event_time_stamp timestamp(14));
#
# Postgresql
# CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp without time zone, event_time_stamp timestamp without time zone);
#
# insert into security(camera, filename, frame, file_type, time_stamp, text_event) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
; sql_query insert into security(camera, filename, frame, file_type, time_stamp, event_time_stamp) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')


############################################################
# Database Options
############################################################

# database type : mysql, postgresql, sqlite3 (default : not defined)
; database_type value

# database to log to (default: not defined)
# for sqlite3, the full path and name for the database.
; database_dbname value

# The host on which the database is located (default: localhost)
; database_host value

# User account name for database (default: not defined)
; database_user value

# User password for database (default: not defined)
; database_password value

# Port on which the database is located
#  mysql 3306 , postgresql 5432 (default: not defined)
; database_port value

# Database wait time in milliseconds for locked database to
# be unlocked before returning database locked error (default 0)
; database_busy_timeout 0



############################################################
# Video Loopback Device (vloopback project)
############################################################

# Output images to a video4linux loopback device
# Specify the device associated with the loopback device
# For example /dev/video1 (default: not defined)
; video_pipe value

# Output motion images to a video4linux loopback device
# Specify the device associated with the loopback device
# For example /dev/video1 (default: not defined)
; motion_video_pipe value


##############################################################
# camera config files - One for each camera.
# Except if only one camera - You only need this config file.
# If you have more than one camera you MUST define one camera
# config file for each camera in addition to this config file.
##############################################################

# Remember: If you have more than one camera you must have one
# camera file for each camera. E.g. 2 cameras requires 3 files:
# This motion.conf file AND camera1.conf and camera2.conf.
# Only put the options that are unique to each camera in the
# camera config files.
; camera /etc/motion/camera1.conf
; camera /etc/motion/camera2.conf
; camera /etc/motion/camera3.conf
; camera /etc/motion/camera4.conf


##############################################################
# Camera config directory
# Any files ending in '.conf' in this directory will be read
# as a camera config file.
##############################################################

; camera_dir /etc/motion/conf.d

2019/07/15

raspberry pi でWEBカメラ ~motion~

pi zero wにカメラをつけてWEBカメラにする。

パソコンで使うUSBカメラを使ったことはあったが、
Camera Module V2を使う。

pi zero wのケースはカメラをセットする穴がある。

ただし、カメラの穴があるふたをするとGPIOの金具があるので閉まらない。

金具部分があいたフタもあるのだが、それにはカメラの穴がない。

どっちかを加工すればいいのだろうが、とりあえずテープで止める。


piでWEBカメラをやる場合の定番としてmotionというソフトがある。

これは動画ではなくて、動きがあった場合のみ画像を更新するものであるが、

外の景色などを表示させるには十分である。


USBカメラの場合、カメラを接続してmotionをインストールすればすぐ使えるのだが、

Camera moduleを使う場合は、 /etc/modulesに以下の記述を追加してrebootが必要。

bcm2835-v4l2


あと、/boot/config.txtに以下の記述が必要なそうなのだが、
私の場合はすでに書いてあった。

start_x=1
gpu_mem=128

start_xって関係なさそうだけどな... まあいい。


vcgencmd get_camera を実施して、両方 1になっていること。

supported=1 detected=1


 ls /dev/video* を実行して、 video0があること。
(私の場合。10,11,12はカメラモジュールを認識しなくても出てくる)

/dev/video0  /dev/video10  /dev/video11  /dev/video12


以下でカメラの動作を確認できる。

(静止画)
raspistill -o test.jpg

-oは出力ファイル名


(動画)
raspivid -o test.h264 -t 10000

-oはファイル名、-tはミリ秒数

形式はh264とかいうものらしいのだが、
VLC media playerで再生できる。


コーデックは H264かMJPEGが指定できるようだ。

-cd, --codec    : Specify the codec to use - H264 (default) or MJPEG

raspivid -cd MJPEG -o test.mjpeg  -t 5000

が、mjpegも結局メディアプレイヤーでは再生できず。


motionは、apt install motion でインストール

apt-get install motion ではダメ、みたいなことがどこかに書いてあったが、
どっちでもできたような気がするが定かではない
(いろいろやったので)

motion.confの設定内容については情報がたくさんあるので特に書かない。


自動起動するために下記の設定をするというのがあるのだが、

/etc/default/motion に

start_motion_daemon=yes

zeroではうまくいかなかった。
psで見るとmotionは起動するようなのだが、ブラウザでアクセスすると起動していないときと同じように表示されない。

sudo motionを実行すると画面が表示されるがグレーで、
「カメラにアクセスできない」みたいなメッセージが表示される。

ログを見ると、すでに起動していてカメラが占有されている、
みたいなことらしい。

USBカメラを使った古いpiではうまく動いていたのだが.....


なので、手動起動にした。

sudo motion -b

-b はバックグラウンド起動のオプション。


psで起動確認

ps aux | grep motion
root       684 96.9  6.6 126476 25320 ?        Sl   22:31  31:29 motion -b
pi        1575  0.0  0.5   4360  1908 pts/0    S+   23:04   0:00 grep --color=auto motion

デーモン起動なので停止する場合はkillする。

もっとスマートな方法があるかな...



しばらく使って気づいたのだが、cameraモジュールはフォーカス(ピント)が手動で、
カメラのレンズ部分を回すことでおこなう。

白いプラスチックのダイヤルみたいなものが付属しているのだが、
それをレンズ部分にはめると回せる。

なくても楊枝かなんかで回せそう。

時計回りで遠くに、逆で近くにフォーカスする。



2019-04-08-raspbian-stretch-lite.img
を使い、諸アップデートをしている。

uname -aの結果
Linux raspberrypi 4.19.57+ #1244 Thu Jul 4 18:42:50 BST 2019 armv6l GNU/Linux